Выпуски Lumen OS

Список собирается из выпусков на GitHub и обновляется сам. Стабильные версии для повседневного просмотра, беты для тех, кто готов проверять новое.

Последние версии

  • XGIMI Z9XСтабильная1.0.10
  • XGIMI Z9XБета1.0.11-beta15
  • XGIMI Z9X HBСтабильная1.0.9
  • XGIMI Z9X HBБета1.0.10-beta21
  • XGIMI Play 6Стабильная1.0.10
  • XGIMI X50 UltraБета1.0.10-beta11
  • XGIMI X50 Ultra MaxБета1.0.10-beta11
  • XGIMI RS30 Ultra MaxБета1.0.10-beta6
  • XGIMI TITAN NoirБета1.0.10-beta3
  • XGIMI TITAN Noir ProБета1.0.10-beta4
  • XGIMI TITAN Noir MaxБета1.0.10-beta4

Данные GitHub на 21 ноября 2026

Все выпуски

XGIMI Z9X 1.0.11-beta15

БетаGitHub

Бета 15 для XGIMI Z9X (G0082). Это тестовая сборка, а не основной выпуск. В ней могут быть ошибки.

Что нового

  • Обновления скачиваются быстрее. Lumen качает файл обновления сразу по нескольким соединениям, поэтому ограничение скорости одного соединения у провайдера почти не мешает. После обрыва сети, паузы или перезапуска загрузка продолжается с того места, где остановилась. Готовый файл проверяется как раньше. Эта бета ещё скачивается по старому, быстрее станут следующие обновления.
  • Меню проектора можно поставить справа: «Все настройки», «Общие», группа «Меню». Там же размер меню: обычный или компактный, в компактном на экран помещается больше строк. Справа меню отражено целиком.
  • «Коррекция изображения»: «Автофокус сейчас» и «Ручной фокус» стоят сразу под ручной коррекцией трапеции, настройки умного автофокуса на своей странице. «Вернуть исходное изображение» теперь называется «Вернуть экран к исходному».
  • Светлая тема: выбранная плитка быстрого меню и выбранная строка в его окнах и в «Все настройки» закрашены более глубоким синим, белый текст на нём читается лучше.
  • Страница «Вывод звука» обновляется сама. После включения eARC сразу видно, что звук идёт на саундбар, закрывать и открывать страницу больше не нужно.
  • Панель «Сигнал» на странице «Для разработчиков»: новые строки «Режим изображения» и «Плавность движения», режим изображения виден и на маленькой карточке. В полной панели ещё данные HDR фильма (яркость и цвета мастеринга, MaxCLL и MaxFALL), имя устройства на входе и скорость линии HDMI. Частота кадров показывается ровно, случайных значений вроде 133 Гц больше нет. Подсказка «Удерживайте OK, чтобы раскрыть» видна каждый раз, когда карточку открывает назначенная ей кнопка пульта, пока вы ни разу её не раскрыли.

Всё новое пока проверено тестами. Если что-то не так, отправьте отчёт в настройках, пункт «Общие» или напишите, что делали и что увидели.

Как получить

Если Lumen OS уже стоит, бета приходит по Wi-Fi на Z9X с Lumen OS 1.0.9, 1.0.10 или с любой бетой 1.0.11. На бетах она придёт сама. На 1.0.9 и 1.0.10 откройте «Настройки», «Об устройстве», «Обновление Lumen OS» и включите «Бета-обновления». Если этой строки нет, сначала нажмите «Проверить обновления», и она появится. Потом проверьте обновления ещё раз. Бета скачивается целиком, около 700 МБ. Данные сохраняются.

Если ставите Lumen OS из системы XGIMI, откройте Lumen Installer, выберите версию «Бета» и подготовьте пробный запуск. Если пробный запуск старой беты уже есть, сначала нажмите «Удалить пробный запуск».

Файлы: lumen-os-1.0.11-beta15-nogms-system.img (образ системы), SHA256SUMS и SHA256SUMS.sig (контрольная сумма и подпись), lumen-os-1.0.11-beta15-nogms-full-ota.zip и lumen-os-1.0.11-beta15-nogms-full-payload_metadata.bin (обновление, его берёт сам проектор).

---

Beta 15 for the XGIMI Z9X (G0082). This is a test build, not a main release. It may have bugs.

What is new

  • Updates download faster. Lumen fetches the update file over several connections at once, so a provider's speed limit per connection hardly matters. After a network drop, a pause or a restart the download goes on from where it stopped. The finished file is checked as before. This beta still downloads the old way, the next updates come faster.
  • The projector menu can sit on the right: All settings, General, the Menu group. The menu size is there too: normal or compact, the compact one fits more rows on the screen. On the right the whole menu is mirrored.
  • Image correction: Autofocus now and Manual focus sit right under the manual keystone, the smart autofocus settings have their own page. Restore the original picture is now called Restore screen to default.
  • Light theme: the selected quick menu tile and the selected row in its windows and in All settings are filled with a deeper blue, the white text on it reads better.
  • The Sound output page updates by itself. After you turn on eARC it shows at once that the sound goes to the soundbar, no need to close and open the page.
  • The Signal panel on the For developers page: new Picture mode and Motion smoothing rows, the picture mode shows on the small card too. The full panel also shows the film's HDR data (mastering brightness and colours, MaxCLL and MaxFALL), the name of the device on the input and the HDMI link speed. The frame rate shows steady, random values such as 133 Hz are gone. The Hold OK to open hint shows every time the card is opened by the remote button you gave it, until you have opened the card once.

Everything new is checked by tests so far. If something does not work right, send a report from General or write what you did and what you saw.

How to get it

If Lumen OS is already installed, the beta comes over Wi-Fi to a Z9X that runs Lumen OS 1.0.9, 1.0.10 or any 1.0.11 beta. On a beta it comes by itself. On 1.0.9 and 1.0.10 open Settings, About, Lumen OS update and turn on Beta updates. If that row is not there, press Check for updates first and it shows up. Then check for updates again. The beta downloads in full, about 700 MB. Your data stays.

If you install Lumen OS from the XGIMI system, open Lumen Installer, choose the Beta version and prepare the trial run. If a trial run of an older beta is already there, press Remove the trial first.

Files: lumen-os-1.0.11-beta15-nogms-system.img (the system image), SHA256SUMS and SHA256SUMS.sig (checksum and signature), lumen-os-1.0.11-beta15-nogms-full-ota.zip and lumen-os-1.0.11-beta15-nogms-full-payload_metadata.bin (the update, the projector takes it by itself).

XGIMI Z9X 1.0.11-beta14

БетаGitHub

Бета 14 для XGIMI Z9X (G0082). Это тестовая сборка, а не основной выпуск. В ней могут быть ошибки.

Что нового

  • Свой звук при включении: короткая светлая мелодия Lumen. Она звучит вместе с заставкой при включении и при выходе из режима ожидания. Переключатель «Мелодия при включении» в «Все настройки», «Общие», «Включение». Если вы раньше выключали мелодию XGIMI, мелодия Lumen тоже выключена. Когда звук выключен или громкость на нуле, мелодии нет.
  • Точка доступа Wi-Fi как в системе XGIMI. Плитка «Сеть» в меню проектора открывает окно: текущая сеть Wi-Fi, «Точка доступа», «Имя сети», «Пароль» и «Сбросить имя и пароль».
  • Адаптация к цвету стены как в системе XGIMI: меню «Трапеция», строка «Адаптация к цвету стены». Проектор снимает стену своей камерой и предлагает новые цвета, их можно сравнить с исходными.
  • Родительский контроль как в системе XGIMI: «Все настройки», «Общие», «Родительский контроль». Пароль из четырёх нажатий стрелок пульта, время за один раз и за день, детский режим с выбранными приложениями.
  • «Включение питания и автозапуск»: проектор включается сам, когда в розетке появляется питание. «Все настройки», «Общие», «Включение».
  • Главный экран появляется сразу после заставки и показывает то, что было на нём перед выключением. Картинки и погода подгружаются следом.
  • Главный экран: выбранный элемент обведён синей рамкой. Страницы витрины сменяются мягким растворением. Витрина советует только то, что уже можно посмотреть, и пишет, где откроется фильм. Приложение с двумя значками теперь стоит одной плиткой.
  • Первая настройка спрашивает тему сразу после языка: Светлая, Тёмная или Авто. Справа видно, как будет выглядеть главный экран.
  • Светлая тема больше не белая: фон тёплый песочный, в тёмной комнате он не слепит. Тема меняется плавно во всех приложениях Lumen.
  • Окно установки и удаления приложений в стиле Lumen. Раньше вопрос «Удалить приложение?» шёл по одной букве в строке.
  • Lumen Play сам получает доступ к файлам и сразу видит субтитры рядом с видео на флешке.
  • Пункты страницы «Настройки проектора» теперь в «Все настройки», «Общие».
  • Новая страница «Для разработчиков» в конце «Все настройки»: панели «Сигнал» и «Датчики» и диагностика. Маленькая карточка сигнала или датчиков раскрывается в полную панель, если удерживать OK. Короткое нажатие OK как и раньше идёт в фильм или приставку.
  • Переключатель «Звуки нажатий» в меню «Звук» и строка «Температура» в общих настройках, как в системе XGIMI. Пункты автофокуса при включении и после перемещения убраны, в системе XGIMI их нет.

Всё новое пока проверено тестами. Если что-то не так, отправьте отчёт в настройках, пункт «Общие» или напишите, что делали и что увидели.

Как получить

Если Lumen OS уже стоит, бета приходит по Wi-Fi на Z9X с Lumen OS 1.0.9, 1.0.10 или с любой бетой 1.0.11. На бетах она придёт сама. На 1.0.9 и 1.0.10 откройте «Настройки», «Об устройстве», «Обновление Lumen OS» и включите «Бета-обновления». Если этой строки нет, сначала нажмите «Проверить обновления», и она появится. Потом проверьте обновления ещё раз. Бета скачивается целиком, около 700 МБ. Данные сохраняются.

Если ставите Lumen OS из системы XGIMI, откройте Lumen Installer, выберите версию «Бета» и подготовьте пробный запуск. Если пробный запуск старой беты уже есть, сначала нажмите «Удалить пробный запуск».

Файлы: lumen-os-1.0.11-beta14-nogms-system.img (образ системы), SHA256SUMS и SHA256SUMS.sig (контрольная сумма и подпись), lumen-os-1.0.11-beta14-nogms-full-ota.zip и lumen-os-1.0.11-beta14-nogms-full-payload_metadata.bin (обновление, его берёт сам проектор).

---

Beta 14 for the XGIMI Z9X (G0082). This is a test build, not a main release. It may have bugs.

What is new

  • Lumen's own power-on sound: a short bright melody. It plays with the boot logo at power-on and when the projector wakes from standby. The Power-on melody switch is in All settings, General, Power on. If you had turned the XGIMI melody off, the Lumen melody is off too. With the sound muted or the volume at zero there is no melody.
  • A Wi-Fi hotspot as in the XGIMI system. The Network tile of the projector menu opens a window: the current Wi-Fi network, Hotspot, Network name, Password and Reset name and password.
  • Wall colour adaptation as in the XGIMI system: the Keystone section, Wall colour adaptation. The projector takes a picture of the wall with its camera and offers new colours that you can compare with the original ones.
  • Parental controls as in the XGIMI system: All settings, General, Parental controls. A password of four presses of the remote's arrows, a time limit per session and per day, a kids mode with the apps you choose.
  • Power on and auto start: the projector turns on by itself when the socket gets power. All settings, General, Power on.
  • The main screen shows right after the boot logo, with what it showed before the projector was turned off. Pictures and the weather load after it.
  • Main screen: a blue frame marks the selected element. Showcase pages change with a soft cross fade. The showcase suggests only what you can watch now and says where the film opens. An app with two launcher icons shows as one tile.
  • The setup wizard asks for the theme right after the language: Light, Dark or Auto. The right side shows how the main screen will look.
  • The light theme is no longer white: the background is a warm sand colour that does not dazzle in a dark room. The theme changes smoothly in every Lumen app.
  • The app install and uninstall window in the Lumen look. Before, the question Uninstall this app? showed one letter per line.
  • Lumen Play gets file access by itself and finds the subtitles next to a video on a USB stick right away.
  • The items of the Projector settings page are now in All settings, General.
  • A new For developers page at the end of All settings: the Signal and Sensors panels and diagnostics. The small signal or sensors card opens into the full panel when you hold OK. A short OK press still goes to the film or the console as before.
  • A Key sounds switch in the Sound section and a Temperature row in the general settings, as in the XGIMI system. The autofocus at power-on and after moving rows are gone, the XGIMI system does not have them.

Everything new is checked by tests so far. If something does not work right, send a report from General or write what you did and what you saw.

How to get it

If Lumen OS is already installed, the beta comes over Wi-Fi to a Z9X that runs Lumen OS 1.0.9, 1.0.10 or any 1.0.11 beta. On a beta it comes by itself. On 1.0.9 and 1.0.10 open Settings, About, Lumen OS update and turn on Beta updates. If that row is not there, press Check for updates first and it shows up. Then check for updates again. The beta downloads in full, about 700 MB. Your data stays.

If you install Lumen OS from the XGIMI system, open Lumen Installer, choose the Beta version and prepare the trial run. If a trial run of an older beta is already there, press Remove the trial first.

Files: lumen-os-1.0.11-beta14-nogms-system.img (the system image), SHA256SUMS and SHA256SUMS.sig (checksum and signature), lumen-os-1.0.11-beta14-nogms-full-ota.zip and lumen-os-1.0.11-beta14-nogms-full-payload_metadata.bin (the update, the projector takes it by itself).

XGIMI X50 Ultra Max 1.0.10-beta9

БетаGitHub

Вышла бета 10, ставьте её: https://github.com/Project-Lumen-OS/lumen-os/releases/tag/x50max-1.0.10-beta10 . Beta 10 is out, use it instead.

Бета 9. Lumen OS для XGIMI X50 Ultra Max (G0100). Только пробный запуск.

На X50 Ultra Max установка насовсем пока закрыта. Она откроется после проверки данных настоящего Ultra Max. Установщик внутри пробы проверит проектор и скажет, что на этой модели пока доступна только проба.

Lumen OS сама обновляется через интернет. На Ultra Max это заработает, когда откроется установка насовсем.

Что нового

  • Главный экран в новом виде «Витрина»: картинка того, что вы смотрите, на весь экран, под ней ряд приложений, входы HDMI и круглые кнопки «Приложения» и «Настройки». Витрина сама листает страницы и меняет их мягким растворением. Каждое приложение стоит одной плиткой, даже если у него два значка запуска. После заставки включения главный экран появляется сразу.
  • Светлая тема теперь тёплого песочного цвета и светит на стену мягче. Так выглядят главный экран, быстрое меню, карточка сигнала и окно установки приложений. Тёмная тема не менялась.
  • Окно установки и удаления приложений в стиле Lumen. Раньше оно было серым, с огромным значком и текстом по букве в строке.
  • Свои режимы изображения, как в заводской прошивке XGIMI: в конце списка режимов пункт «Пользовательский». Новый режим копирует текущий и помнит свои настройки.
  • Точка доступа Wi-Fi, как в заводской прошивке: плитка «Сеть» в меню проектора, там же имя сети и пароль.
  • Адаптация к цвету стены, как в заводской прошивке: раздел «Трапеция», строка «Адаптация к цвету стены».
  • «Все настройки», раздел «Общие», как в заводской прошивке: «Включение питания и автозапуск» (проектор сам включается, когда появляется питание), «Мелодия при включении» (новая мелодия Lumen при выходе из режима ожидания), «Режим большой высоты», заставка «Запускать через», «Управление по последовательному порту» (команды RS-232 через переходник USB) и «Родительский контроль».
  • Кнопка источника на пульте как в заводской прошивке: каждое нажатие сразу переключает вход, слева вверху на три секунды видна маленькая карточка.
  • Новая страница «Для разработчиков» в конце «Все настройки»: панели «Сигнал» и «Датчики». Маленькая карточка раскрывается в полную панель долгим нажатием OK. Панель «Сигнал» теперь читает приёмник HDMI проектора: формат и глубину цвета, цветовое пространство, данные HDR, устройство на входе и скорость соединения.
  • Lumen Play сразу видит файлы на флешке, например субтитры рядом с видео. Доступ к файлам он получает сам.
  • Настройки, «Об устройстве»: код модели XGIMI, версия прошивки XGIMI, контроллер DLP и FPGA, а также экран возврата к системе XGIMI с именем файла для флешки.

Всё новое в этой бете пока проверено только тестами и на эмуляторе, на Ultra Max ещё нет.

Что нужно знать

  • Это бета для тестеров. Lumen OS запускается как проба поверх системы XGIMI. Система XGIMI не меняется.
  • Пробу ставит приложение Lumen Installer: на X50 оно само берёт бету.

Как вернуться

  • Просто перезагрузите проектор. Он запустит систему XGIMI, как раньше.
  • Если система XGIMI вдруг не запускается, верните её с флешки. Флешка: таблица MBR, один раздел FAT32, в корне только файл прошивки XGIMI_HORSEPOPULAR_XR03E.bin. На Mac копируйте командой cp -X. Вставьте флешку, выдерните шнур питания, зажмите кнопку питания на самом проекторе, вставьте шнур и держите кнопку, пока не появится экран обновления (около 5 секунд). Не отключайте питание, пока идёт обновление. Всё на проекторе сотрётся. V1.2.54: https://product-library.static.xgimi.com/firmware/release/MTK9681/diana/MTK9681_DOHKO_1.2.54_20260615-231328/XGIMI_HORSEPOPULAR_XR03E.bin

Что проверить и прислать

  • Главный экран и светлую тему, свои режимы изображения, точку доступа, адаптацию к цвету стены, панель «Сигнал» с приставкой по HDMI.
  • Если что-то не работает, напишите модель, версию прошивки XGIMI и что делали.

Файлы: lumen-os-x50max-1.0.10-beta9-nogms-system.img, SHA256SUMS и SHA256SUMS.sig (подпись ключом этой модели), пакет обновления lumen-os-x50max-1.0.10-beta9-nogms-full-ota.zip с файлом -payload_metadata.bin. Для X50 Ultra есть свой выпуск: x50-1.0.10-beta9.

---

Beta 9. Lumen OS for the XGIMI X50 Ultra Max (G0100). Trial only.

Installing for good is not open on the X50 Ultra Max yet. It opens once the data of a real Ultra Max has been checked. The installer inside the trial checks the projector and tells you that this model can only be tried for now.

Lumen OS updates itself over the internet. On the Ultra Max this starts once installing for good opens.

New

  • A new home screen look, "Showcase": a full screen picture of what you watch, below it one row of apps, the HDMI inputs and the round "Apps" and "Settings" buttons. The showcase turns its pages by itself with a soft cross fade. Every app has one tile, even an app with two launch icons. The home screen shows right after the start-up animation.
  • The light theme is now a warm sand colour and is softer on the wall. This is how the home screen, the quick menu, the signal card and the app install window look. The dark theme did not change.
  • The app install and uninstall window in the Lumen style. Before, it was grey, with a huge icon and its text one letter per line.
  • Your own picture modes, as in the XGIMI system: "Custom" at the end of the picture mode list. A new mode copies the current one and keeps its own settings.
  • Wi-Fi hotspot, as in the XGIMI system: the "Network" tile in the projector menu, with the network name and password there too.
  • Wall colour adaptation, as in the XGIMI system: the "Keystone" section, "Wall colour adaptation".
  • "All settings", "General", as in the XGIMI system: "Power on and auto start" (the projector starts by itself when power comes back), "Power-on melody" (a new Lumen melody when it wakes from standby), "High altitude mode", the screensaver "Start after" time, "Serial port control" (RS-232 commands through a USB adapter) and "Parental controls".
  • The source button on the remote works as in the XGIMI system: each press switches to the next input at once, a small card shows for three seconds in the top left.
  • A new "Developer options" page at the end of "All settings": the "Signal" and "Sensors" panels. Hold OK on the small card to open the full panel. The "Signal" panel now reads the projector's HDMI receiver: colour format and depth, colour space, HDR data, the device on the input and the link speed.
  • Lumen Play sees the files on a USB stick at once, for example subtitles next to a video. It gets file access by itself.
  • Settings, "About": the XGIMI model code, the XGIMI firmware version, the DLP controller and FPGA, and a screen with the way back to the XGIMI system and the file name for the stick.

Everything new in this beta is checked by tests and on an emulator only so far, not on an Ultra Max yet.

Good to know

  • This is a beta for testers. Lumen OS runs as a trial on top of the XGIMI system. The XGIMI system does not change.
  • The trial is started by the Lumen Installer app: on the X50 it takes the beta by itself.

How to go back

  • Just restart the projector. It starts the XGIMI system as before.
  • If the XGIMI system does not start, bring it back from a USB stick. The stick: MBR, one FAT32 partition, only the firmware file XGIMI_HORSEPOPULAR_XR03E.bin in its root. On a Mac copy it with cp -X. Put the stick in, unplug the projector, hold the power button on the projector itself, plug it in and keep holding until the update screen shows (about 5 seconds). Do not cut the power while it updates. Everything on the projector is erased. V1.2.54: https://product-library.static.xgimi.com/firmware/release/MTK9681/diana/MTK9681_DOHKO_1.2.54_20260615-231328/XGIMI_HORSEPOPULAR_XR03E.bin

What to check and send

  • The home screen and the light theme, your own picture modes, the hotspot, wall colour adaptation, the "Signal" panel with a player on HDMI.
  • If something does not work, write your model, XGIMI firmware version and what you did.

Files: lumen-os-x50max-1.0.10-beta9-nogms-system.img, SHA256SUMS and SHA256SUMS.sig (signed with this model's key), the update package lumen-os-x50max-1.0.10-beta9-nogms-full-ota.zip with its -payload_metadata.bin file. The X50 Ultra has its own release: x50-1.0.10-beta9.

XGIMI X50 Ultra 1.0.10-beta9

БетаGitHub

Вышла бета 10, ставьте её: https://github.com/Project-Lumen-OS/lumen-os/releases/tag/x50-1.0.10-beta10 . Бета 9 получает её сама через интернет в пункте «Обновление Lumen OS». Beta 10 is out, use it instead. Beta 9 gets it by itself over the internet in "Lumen OS update".

Бета 9. Lumen OS для XGIMI X50 Ultra (G0111).

Lumen OS сама обновляется через интернет. Бета 7 и бета 8 получают бету 9 в пункте «Обновление Lumen OS» в настройках. Обновление скачивается целиком, около 700 МБ. Данные сохраняются.

Бета 5 и бета 6 сами не обновляются. Скопируйте на флешку файл Lumen Installer с окончанием .apk со страницы https://github.com/Project-Lumen-OS/lumen-installer/releases/latest и поставьте его из «Файлов» на главном экране. Откройте Lumen Installer, нажмите «Обновить Lumen OS» и подтвердите. Потом нажмите «Открыть Обновление Lumen OS» и «Загрузить и установить». Данные сохраняются.

Бета 4 не умеет обновляться через интернет. Чтобы перейти с неё, верните систему XGIMI с флешки (ниже) и установите бету 9 из пробного запуска.

Что нового

  • Главный экран в новом виде «Витрина»: картинка того, что вы смотрите, на весь экран, под ней ряд приложений, входы HDMI и круглые кнопки «Приложения» и «Настройки». Витрина сама листает страницы и меняет их мягким растворением. Каждое приложение стоит одной плиткой, даже если у него два значка запуска. После заставки включения главный экран появляется сразу.
  • Светлая тема теперь тёплого песочного цвета и светит на стену мягче. Так выглядят главный экран, быстрое меню, карточка сигнала и окно установки приложений. Тёмная тема не менялась.
  • Окно установки и удаления приложений в стиле Lumen. Раньше оно было серым, с огромным значком и текстом по букве в строке.
  • Свои режимы изображения, как в заводской прошивке XGIMI: в конце списка режимов пункт «Пользовательский». Новый режим копирует текущий и помнит свои настройки.
  • Точка доступа Wi-Fi, как в заводской прошивке: плитка «Сеть» в меню проектора, там же имя сети и пароль.
  • Адаптация к цвету стены, как в заводской прошивке: раздел «Трапеция», строка «Адаптация к цвету стены».
  • «Все настройки», раздел «Общие», как в заводской прошивке: «Включение питания и автозапуск» (проектор сам включается, когда появляется питание), «Мелодия при включении» (новая мелодия Lumen при выходе из режима ожидания), «Режим большой высоты», заставка «Запускать через», «Управление по последовательному порту» (команды RS-232 через переходник USB) и «Родительский контроль».
  • Кнопка источника на пульте как в заводской прошивке: каждое нажатие сразу переключает вход, слева вверху на три секунды видна маленькая карточка.
  • Новая страница «Для разработчиков» в конце «Все настройки»: панели «Сигнал» и «Датчики». Маленькая карточка раскрывается в полную панель долгим нажатием OK. Панель «Сигнал» теперь читает приёмник HDMI проектора: формат и глубину цвета, цветовое пространство, данные HDR, устройство на входе и скорость соединения.
  • Lumen Play сразу видит файлы на флешке, например субтитры рядом с видео. Доступ к файлам он получает сам.
  • Настройки, «Об устройстве»: код модели XGIMI, версия прошивки XGIMI, контроллер DLP и FPGA, а также экран возврата к системе XGIMI с именем файла для флешки.

Всё новое в этой бете пока проверено только тестами и на эмуляторе.

Перед установкой

  • Нужна прошивка XGIMI V1.2.64. С V1.2.54 работает только проба.
  • Пробу ставит приложение Lumen Installer. Установить насовсем можно внутри пробы: пункт «Установить Lumen OS» на главном экране.
  • Установка стирает всё на проекторе: приложения, аккаунты, настройки и файлы.

Как вернуть систему XGIMI

  • После установки систему XGIMI возвращает только флешка. В Lumen OS нет кнопки возврата.
  • Флешка: таблица MBR, один раздел FAT32, в корне только файл XGIMI_HORSEPOPULAR_XR04E.bin. Для X50 Ultra Max файл называется XGIMI_HORSEPOPULAR_XR03E.bin, ссылка на него в выпуске для Ultra Max. На Mac копируйте командой cp -X. Ссылка: https://product-library.static.xgimi.com/firmware/release/MTK9681/diana/MTK9681_DOHKO_1.2.64_20260629-115816/XGIMI_HORSEPOPULAR_XR04E.bin
  • Вставьте флешку, выдерните шнур питания, зажмите кнопку питания на самом проекторе, вставьте шнур и держите кнопку, пока не появится экран обновления (около 5 секунд). Не отключайте питание, пока идёт обновление. Всё на проекторе сотрётся, запустится система XGIMI.
  • Картинки нет больше 15 минут после установки или обновления: выдерните шнур, вставьте его снова и включите проектор коротким нажатием. После нескольких неудачных запусков проектор сам вернётся к прежней системе.

Что проверить и прислать

  • Главный экран и светлую тему, свои режимы изображения, точку доступа, адаптацию к цвету стены, мелодию при выходе из режима ожидания, автозапуск при появлении питания, панель «Сигнал» с приставкой по HDMI.
  • Если что-то не работает, напишите модель, версию прошивки XGIMI и что делали.

Файлы: lumen-os-x50-1.0.10-beta9-nogms-system.img, SHA256SUMS и SHA256SUMS.sig (подпись ключом этой модели), пакет обновления lumen-os-x50-1.0.10-beta9-nogms-full-ota.zip с файлом -payload_metadata.bin для обновления через интернет. Для X50 Ultra Max есть свой выпуск x50max-1.0.10-beta9, там пока только проба.

---

Beta 9. Lumen OS for the XGIMI X50 Ultra (G0111).

Lumen OS updates itself over the internet. Beta 7 and beta 8 get beta 9 in "Lumen OS update" in the settings. The update downloads in full, about 700 MB. Your data stays.

Beta 5 and beta 6 do not update by themselves. Copy the Lumen Installer file that ends in .apk from https://github.com/Project-Lumen-OS/lumen-installer/releases/latest to a USB stick and install it from Files on the home screen. Open Lumen Installer, press "Update Lumen OS" and confirm. Then press "Open Lumen OS update" and "Download and install". Your data stays.

Beta 4 cannot update over the internet. To move from it, bring the XGIMI system back from the USB stick (below) and install beta 9 from the trial.

New

  • A new home screen look, "Showcase": a full screen picture of what you watch, below it one row of apps, the HDMI inputs and the round "Apps" and "Settings" buttons. The showcase turns its pages by itself with a soft cross fade. Every app has one tile, even an app with two launch icons. The home screen shows right after the start-up animation.
  • The light theme is now a warm sand colour and is softer on the wall. This is how the home screen, the quick menu, the signal card and the app install window look. The dark theme did not change.
  • The app install and uninstall window in the Lumen style. Before, it was grey, with a huge icon and its text one letter per line.
  • Your own picture modes, as in the XGIMI system: "Custom" at the end of the picture mode list. A new mode copies the current one and keeps its own settings.
  • Wi-Fi hotspot, as in the XGIMI system: the "Network" tile in the projector menu, with the network name and password there too.
  • Wall colour adaptation, as in the XGIMI system: the "Keystone" section, "Wall colour adaptation".
  • "All settings", "General", as in the XGIMI system: "Power on and auto start" (the projector starts by itself when power comes back), "Power-on melody" (a new Lumen melody when it wakes from standby), "High altitude mode", the screensaver "Start after" time, "Serial port control" (RS-232 commands through a USB adapter) and "Parental controls".
  • The source button on the remote works as in the XGIMI system: each press switches to the next input at once, a small card shows for three seconds in the top left.
  • A new "Developer options" page at the end of "All settings": the "Signal" and "Sensors" panels. Hold OK on the small card to open the full panel. The "Signal" panel now reads the projector's HDMI receiver: colour format and depth, colour space, HDR data, the device on the input and the link speed.
  • Lumen Play sees the files on a USB stick at once, for example subtitles next to a video. It gets file access by itself.
  • Settings, "About": the XGIMI model code, the XGIMI firmware version, the DLP controller and FPGA, and a screen with the way back to the XGIMI system and the file name for the stick.

Everything new in this beta is checked by tests and on an emulator only so far.

Before you install

  • Your projector needs XGIMI firmware V1.2.64. With V1.2.54 only the trial works.
  • The trial is started by the Lumen Installer app. Installing for good is done inside the trial: the home screen shows "Install Lumen OS".
  • Installing erases everything on the projector: apps, accounts, settings and files.

How to get the XGIMI system back

  • After an install only the USB stick brings the XGIMI system back. Lumen OS has no button to go back.
  • The stick: MBR, one FAT32 partition, only the file XGIMI_HORSEPOPULAR_XR04E.bin in its root. For the X50 Ultra Max the file is named XGIMI_HORSEPOPULAR_XR03E.bin, its link is in the Ultra Max release. On a Mac copy it with cp -X. Link: https://product-library.static.xgimi.com/firmware/release/MTK9681/diana/MTK9681_DOHKO_1.2.64_20260629-115816/XGIMI_HORSEPOPULAR_XR04E.bin
  • Put the stick in, unplug the projector, hold the power button on the projector itself, plug it in and keep holding until the update screen shows (about 5 seconds). Do not cut the power while it updates. Everything on the projector is erased and the XGIMI system starts.
  • No picture for more than 15 minutes after an install or an update: unplug the projector, plug it in again and switch it on with a short press. After a few failed starts the projector goes back to the system it had before by itself.

What to check and send

  • The home screen and the light theme, your own picture modes, the hotspot, wall colour adaptation, the melody when it wakes from standby, auto start when power comes back, the "Signal" panel with a player on HDMI.
  • If something does not work, write your model, XGIMI firmware version and what you did.

Files: lumen-os-x50-1.0.10-beta9-nogms-system.img, SHA256SUMS and SHA256SUMS.sig (signed with this model's key), the update package lumen-os-x50-1.0.10-beta9-nogms-full-ota.zip with its -payload_metadata.bin file for the update over the internet. The X50 Ultra Max has its own release x50max-1.0.10-beta9, trial only for now.

XGIMI TITAN Noir Pro 1.0.10-beta4

БетаGitHub

Бета 4. Lumen OS для XGIMI TITAN Noir Pro (H0062). Только пробный запуск.

Что нового

  • Главный экран: у каждого из трёх входов HDMI своя кнопка внизу. Теперь там HDMI 1, HDMI 2, HDMI 3 и ещё одна кнопка: флешка или «Источник» со всем остальным. Раньше HDMI 3 прятался за кнопкой «Источник», если была подключена флешка или повтор экрана.
  • Кнопки пульта: в список действий добавлены «HDMI 3» и «Датчики». Выбранная строка на странице кнопок теперь светлая с тёмным текстом, как в меню проектора.
  • Режим Dolby Vision: новая строка с выбором «Dolby Vision Bright» и «Dolby Vision Dark», как в заводской прошивке XGIMI. Она стоит над «Настройками Dolby Vision» и работает, пока идёт видео Dolby Vision.
  • «Все настройки», HDMI, «Параметры входа»: страница в новом виде меню, светлая или тёмная по теме. Переключатели вместо флажков, «Источник при включении» меняется кнопками влево и вправо, внизу входы HDMI и что к ним подключено.
  • Панель «Сигнал» больше не пишет «DVI, без звука» при обычном HDMI со звуком. Строка «Режим входа» называется «Режим HDMI», как в меню, строка «Порт» называется «Возможности порта». Строка «Плавность» теперь «Кадровая частота», её легко было спутать с «Плавностью движения» из меню.
  • Карточка «Датчики» стоит справа, там же, где карточка сигнала, и долгое нажатие OK раскрывает её на месте. Пока на экране карточка сигнала или датчиков, долгое нажатие OK на главном экране раскрывает карточку и больше не открывает меню плитки.
  • Голосовой поиск: «IPTV», «ТВ каналы», «телевизор» и такие же слова на других языках больше не открывают Lumen Play. Открывается установленное приложение для телеканалов или Lampa, а если их нет, поиск.

Проба запускается на английском. Русский и другие языки, а также часовой пояс выбираются в настройках Android. Эта бета на настоящем TITAN Noir Pro ещё не запускалась, всё новое проверено только тестами и на эмуляторе. Если что-то не так, напишите.

Как запустить пробу

  • Нужна прошивка XGIMI V1.2.99 или V1.2.54.
  • Скачайте файл Lumen Installer, который заканчивается на .apk1, отсюда: https://github.com/Project-Lumen-OS/lumen-installer/releases/latest Если Lumen Installer уже стоит, обновите его оттуда же. Как поставить приложение с флешки, написано в инструкции: https://github.com/Project-Lumen-OS/lumen-os/blob/main/docs/install/ru.md
  • Откройте Lumen Installer. У этой модели есть только бета, она и будет выбрана. Нажмите «Подготовить пробный запуск», потом «Запустить Lumen OS» и перезапустите проектор.
  • Файлы этого выпуска скачивать не нужно, Lumen Installer берёт их сам.

Как вернуться в систему XGIMI

  • Просто перезапустите проектор. Система XGIMI запустится как была, проба в ней ничего не меняет.

Если система XGIMI сама не запускается

  • Так быть не должно. Вернуть её можно флешкой восстановления: таблица MBR, формат FAT32, в корне только файл XGIMI_HORSEPOPULAR_XR04EOS.bin (прошивка V1.2.99, 2 519 405 360 байт). На Mac копируйте командой cp -X. Ссылка: https://product-library.static.xgimi.com/firmware/release/MTK9681/dianahy/MTK9681_DOHKO_1.2.99_20260907-104602/XGIMI_HORSEPOPULAR_XR04EOS.bin
  • Вставьте флешку, выдерните шнур питания, зажмите кнопку питания на самом проекторе, вставьте шнур и держите кнопку, пока не появится экран обновления. Всё на проекторе сотрётся, запустится система XGIMI.

Что проверить и прислать

  • Кнопки HDMI 1, HDMI 2 и HDMI 3 на главном экране, режим Dolby Vision с видео Dolby Vision, строку «Подключение» в панели «Сигнал» с приставкой по HDMI, страницу «Параметры входа», карточку «Датчики», голосовой поиск со словами «ТВ каналы».
  • Если что-то не работает, напишите модель, версию прошивки XGIMI и что делали.

Что пока нельзя

  • Установить Lumen OS насовсем.

---

Beta 4. Lumen OS for the XGIMI TITAN Noir Pro (H0062). Trial only.

New

  • Home screen: each of the three HDMI inputs has its own button at the bottom. Now there are HDMI 1, HDMI 2, HDMI 3 and one more button: the USB stick or Source with everything else. Before, HDMI 3 hid behind the Source button when a USB stick or screen mirroring was there.
  • Remote buttons: HDMI 3 and Sensors are now in the list of actions. The selected row on the buttons page is now light with dark text, as in the projector menu.
  • Dolby Vision mode: a new row with Dolby Vision Bright and Dolby Vision Dark, as in the XGIMI factory firmware. It sits above Dolby Vision settings and works while Dolby Vision video plays.
  • All settings, HDMI, Input options: the page has the new menu look, light or dark with the theme. Switches instead of checkboxes, Source at power on changes with left and right, the HDMI inputs and what is connected to them at the bottom.
  • The Signal panel no longer says DVI, no sound for normal HDMI with sound. The Input mode row is now called HDMI mode, as in the menu, the Port row is now called Port features. The Smoothness row is now Frame rate, it was easy to mix up with Motion smoothing in the menu.
  • The Sensors card sits on the right, where the signal card is, and a long press of OK opens it in place. While the signal or sensors card is on the screen, a long press of OK on the home screen opens the card and no longer opens the tile menu.
  • Voice search: IPTV, TV channels, television and the same words in the other languages no longer open Lumen Play. An installed TV channels app or Lampa opens, and search when there is none.

The trial starts in English. Other languages and your time zone are in the Android settings. This beta has not run on a real TITAN Noir Pro yet, everything new is checked by tests and on an emulator only. If something is wrong, write to us.

How to start the trial

  • Your projector needs XGIMI firmware V1.2.99 or V1.2.54.
  • Download the Lumen Installer file that ends in .apk1 from https://github.com/Project-Lumen-OS/lumen-installer/releases/latest If Lumen Installer is already on the projector, update it from the same page. How to put the app on the projector from a USB stick: https://github.com/Project-Lumen-OS/lumen-os/blob/main/docs/install/en.md
  • Open Lumen Installer. This model has only a beta, so the beta is chosen. Press "Get the trial ready", then "Start Lumen OS", then restart the projector.
  • You do not need to download the files of this release, Lumen Installer gets them itself.

How to go back to the XGIMI system

  • Just restart the projector. The XGIMI system starts as it was, the trial does not change it.

If the XGIMI system does not start by itself

  • This should not happen. A recovery USB stick brings it back: MBR, FAT32 format, only the file XGIMI_HORSEPOPULAR_XR04EOS.bin on the stick itself, not in a folder (firmware V1.2.99, 2 519 405 360 bytes). On a Mac copy it with cp -X. Link: https://product-library.static.xgimi.com/firmware/release/MTK9681/dianahy/MTK9681_DOHKO_1.2.99_20260907-104602/XGIMI_HORSEPOPULAR_XR04EOS.bin
  • Put the stick in, unplug the projector, hold the power button on the projector itself, plug it in and keep holding until the update screen shows. Everything on the projector is erased and the XGIMI system starts.

What to check and send

  • The HDMI 1, HDMI 2 and HDMI 3 buttons on the home screen, Dolby Vision mode with Dolby Vision video, the Connection row of the Signal panel with a console on HDMI, the Input options page, the Sensors card, voice search with the words TV channels.
  • If something does not work, write your model, XGIMI firmware version and what you did.

Not yet

  • Installing Lumen OS for good.

XGIMI TITAN Noir Max 1.0.10-beta4

БетаGitHub

Бета 4. Lumen OS для XGIMI TITAN Noir Max (H0063). Только пробный запуск.

Что нового

  • Главный экран: у каждого из трёх входов HDMI своя кнопка внизу. Теперь там HDMI 1, HDMI 2, HDMI 3 и ещё одна кнопка: флешка или «Источник» со всем остальным. Раньше HDMI 3 прятался за кнопкой «Источник», если была подключена флешка или повтор экрана.
  • Кнопки пульта: в список действий добавлены «HDMI 3» и «Датчики». Выбранная строка на странице кнопок теперь светлая с тёмным текстом, как в меню проектора.
  • Режим Dolby Vision: новая строка с выбором «Dolby Vision Bright» и «Dolby Vision Dark», как в заводской прошивке XGIMI. Она стоит над «Настройками Dolby Vision» и работает, пока идёт видео Dolby Vision.
  • «Все настройки», HDMI, «Параметры входа»: страница в новом виде меню, светлая или тёмная по теме. Переключатели вместо флажков, «Источник при включении» меняется кнопками влево и вправо, внизу входы HDMI и что к ним подключено.
  • Панель «Сигнал» больше не пишет «DVI, без звука» при обычном HDMI со звуком. Строка «Режим входа» называется «Режим HDMI», как в меню, строка «Порт» называется «Возможности порта». Строка «Плавность» теперь «Кадровая частота», её легко было спутать с «Плавностью движения» из меню.
  • Карточка «Датчики» стоит справа, там же, где карточка сигнала, и долгое нажатие OK раскрывает её на месте. Пока на экране карточка сигнала или датчиков, долгое нажатие OK на главном экране раскрывает карточку и больше не открывает меню плитки.
  • Голосовой поиск: «IPTV», «ТВ каналы», «телевизор» и такие же слова на других языках больше не открывают Lumen Play. Открывается установленное приложение для телеканалов или Lampa, а если их нет, поиск.

Проба запускается на английском. Русский и другие языки, а также часовой пояс выбираются в настройках Android. Эта бета на настоящем TITAN Noir Max ещё не запускалась, всё новое проверено только тестами и на эмуляторе. Если что-то не так, напишите.

Как запустить пробу

  • Нужна прошивка XGIMI V1.2.99 или V1.2.54.
  • Скачайте файл Lumen Installer, который заканчивается на .apk1, отсюда: https://github.com/Project-Lumen-OS/lumen-installer/releases/latest Если Lumen Installer уже стоит, обновите его оттуда же. Как поставить приложение с флешки, написано в инструкции: https://github.com/Project-Lumen-OS/lumen-os/blob/main/docs/install/ru.md
  • Откройте Lumen Installer. У этой модели есть только бета, она и будет выбрана. Нажмите «Подготовить пробный запуск», потом «Запустить Lumen OS» и перезапустите проектор.
  • Файлы этого выпуска скачивать не нужно, Lumen Installer берёт их сам.

Как вернуться в систему XGIMI

  • Просто перезапустите проектор. Система XGIMI запустится как была, проба в ней ничего не меняет.

Если система XGIMI сама не запускается

  • Так быть не должно. Вернуть её можно флешкой восстановления: таблица MBR, формат FAT32, в корне только файл XGIMI_HORSEPOPULAR_XR03EOS.bin (прошивка V1.2.99, 2 519 405 360 байт). На Mac копируйте командой cp -X. Ссылка: https://product-library.static.xgimi.com/firmware/release/MTK9681/dianahy/MTK9681_DOHKO_1.2.99_20260907-104602/XGIMI_HORSEPOPULAR_XR03EOS.bin
  • Вставьте флешку, выдерните шнур питания, зажмите кнопку питания на самом проекторе, вставьте шнур и держите кнопку, пока не появится экран обновления. Всё на проекторе сотрётся, запустится система XGIMI.

Что проверить и прислать

  • Кнопки HDMI 1, HDMI 2 и HDMI 3 на главном экране, режим Dolby Vision с видео Dolby Vision, строку «Подключение» в панели «Сигнал» с приставкой по HDMI, страницу «Параметры входа», карточку «Датчики», голосовой поиск со словами «ТВ каналы».
  • Если что-то не работает, напишите модель, версию прошивки XGIMI и что делали.

Что пока нельзя

  • Установить Lumen OS насовсем.

---

Beta 4. Lumen OS for the XGIMI TITAN Noir Max (H0063). Trial only.

New

  • Home screen: each of the three HDMI inputs has its own button at the bottom. Now there are HDMI 1, HDMI 2, HDMI 3 and one more button: the USB stick or Source with everything else. Before, HDMI 3 hid behind the Source button when a USB stick or screen mirroring was there.
  • Remote buttons: HDMI 3 and Sensors are now in the list of actions. The selected row on the buttons page is now light with dark text, as in the projector menu.
  • Dolby Vision mode: a new row with Dolby Vision Bright and Dolby Vision Dark, as in the XGIMI factory firmware. It sits above Dolby Vision settings and works while Dolby Vision video plays.
  • All settings, HDMI, Input options: the page has the new menu look, light or dark with the theme. Switches instead of checkboxes, Source at power on changes with left and right, the HDMI inputs and what is connected to them at the bottom.
  • The Signal panel no longer says DVI, no sound for normal HDMI with sound. The Input mode row is now called HDMI mode, as in the menu, the Port row is now called Port features. The Smoothness row is now Frame rate, it was easy to mix up with Motion smoothing in the menu.
  • The Sensors card sits on the right, where the signal card is, and a long press of OK opens it in place. While the signal or sensors card is on the screen, a long press of OK on the home screen opens the card and no longer opens the tile menu.
  • Voice search: IPTV, TV channels, television and the same words in the other languages no longer open Lumen Play. An installed TV channels app or Lampa opens, and search when there is none.

The trial starts in English. Other languages and your time zone are in the Android settings. This beta has not run on a real TITAN Noir Max yet, everything new is checked by tests and on an emulator only. If something is wrong, write to us.

How to start the trial

  • Your projector needs XGIMI firmware V1.2.99 or V1.2.54.
  • Download the Lumen Installer file that ends in .apk1 from https://github.com/Project-Lumen-OS/lumen-installer/releases/latest If Lumen Installer is already on the projector, update it from the same page. How to put the app on the projector from a USB stick: https://github.com/Project-Lumen-OS/lumen-os/blob/main/docs/install/en.md
  • Open Lumen Installer. This model has only a beta, so the beta is chosen. Press "Get the trial ready", then "Start Lumen OS", then restart the projector.
  • You do not need to download the files of this release, Lumen Installer gets them itself.

How to go back to the XGIMI system

  • Just restart the projector. The XGIMI system starts as it was, the trial does not change it.

If the XGIMI system does not start by itself

  • This should not happen. A recovery USB stick brings it back: MBR, FAT32 format, only the file XGIMI_HORSEPOPULAR_XR03EOS.bin on the stick itself, not in a folder (firmware V1.2.99, 2 519 405 360 bytes). On a Mac copy it with cp -X. Link: https://product-library.static.xgimi.com/firmware/release/MTK9681/dianahy/MTK9681_DOHKO_1.2.99_20260907-104602/XGIMI_HORSEPOPULAR_XR03EOS.bin
  • Put the stick in, unplug the projector, hold the power button on the projector itself, plug it in and keep holding until the update screen shows. Everything on the projector is erased and the XGIMI system starts.

What to check and send

  • The HDMI 1, HDMI 2 and HDMI 3 buttons on the home screen, Dolby Vision mode with Dolby Vision video, the Connection row of the Signal panel with a console on HDMI, the Input options page, the Sensors card, voice search with the words TV channels.
  • If something does not work, write your model, XGIMI firmware version and what you did.

Not yet

  • Installing Lumen OS for good.

XGIMI TITAN Noir Pro 1.0.10-beta3

БетаGitHub

Вышла бета 4, ставьте её: https://github.com/Project-Lumen-OS/lumen-os/releases/tag/titanpro-1.0.10-beta4 . Beta 4 is out, use it instead.

Бета 3. Lumen OS для XGIMI TITAN Noir Pro (H0062). Только пробный запуск.

Что нового

  • Новый мастер первой настройки, как на Z9X: сразу после языка шаг «Оформление» со светлой, тёмной или автоматической темой. Раньше в сборке оставался мастер из версии 1.0.9.
  • При включении из розетки мелодия Lumen звучит вместе с заставкой. Раньше она звучала только при выходе из режима ожидания.
  • Меню проектора можно поставить справа: «Все настройки», «Общие», группа «Меню». Там же размер меню: обычный или компактный, в компактном на экран помещается больше строк. Справа меню отражено целиком.
  • «Коррекция изображения»: «Автофокус сейчас» и «Ручной фокус» стоят сразу под ручной коррекцией трапеции, настройки умного автофокуса на своей странице. «Вернуть исходное изображение» теперь называется «Вернуть экран к исходному».
  • Игровой режим: настройки изображения больше не закрыты целиком. Закрыты только строки, которые добавляют задержку: компенсация движения, шумоподавление, суперразрешение и Ultra 120 Гц.
  • «Анти-радуга» больше не сбрасывает цветовую температуру, а включение и выключение игрового режима не выключает динамическое тональное отображение HDR10. После смены режима изображения меню снова ставит вашу резкость.
  • Меню больше не закрывается, когда вход HDMI перезапускает экран при согласовании сигнала.
  • Светлая тема: выбранная плитка быстрого меню и выбранная строка в его окнах и в «Все настройки» закрашены более глубоким синим, белый текст на нём читается лучше.
  • Панель «Сигнал»: новые строки «Режим изображения» и «Плавность движения», названия те же, что в меню. Режим изображения виден и на маленькой карточке.

Проба запускается на английском. Русский и другие языки, а также часовой пояс выбираются в настройках Android. Эта бета на настоящем TITAN Noir Pro ещё не запускалась, всё новое проверено только тестами и на эмуляторе. Если что-то не так, напишите.

Как запустить пробу

  • Нужна прошивка XGIMI V1.2.99 или V1.2.54.
  • Скачайте файл Lumen Installer, который заканчивается на .apk1, отсюда: https://github.com/Project-Lumen-OS/lumen-installer/releases/latest Если Lumen Installer уже стоит, обновите его оттуда же. Как поставить приложение с флешки, написано в инструкции: https://github.com/Project-Lumen-OS/lumen-os/blob/main/docs/install/ru.md
  • Откройте Lumen Installer. У этой модели есть только бета, она и будет выбрана. Нажмите «Подготовить пробный запуск», потом «Запустить Lumen OS» и перезапустите проектор.
  • Файлы этого выпуска скачивать не нужно, Lumen Installer берёт их сам.

Как вернуться в систему XGIMI

  • Просто перезапустите проектор. Система XGIMI запустится как была, проба в ней ничего не меняет.

Если система XGIMI сама не запускается

  • Так быть не должно. Вернуть её можно флешкой восстановления: таблица MBR, формат FAT32, в корне только файл XGIMI_HORSEPOPULAR_XR04EOS.bin (прошивка V1.2.99, 2 519 405 360 байт). На Mac копируйте командой cp -X. Ссылка: https://product-library.static.xgimi.com/firmware/release/MTK9681/dianahy/MTK9681_DOHKO_1.2.99_20260907-104602/XGIMI_HORSEPOPULAR_XR04EOS.bin
  • Вставьте флешку, выдерните шнур питания, зажмите кнопку питания на самом проекторе, вставьте шнур и держите кнопку, пока не появится экран обновления. Всё на проекторе сотрётся, запустится система XGIMI.

Что проверить и прислать

  • Мелодию при включении из розетки, первую настройку пробы, меню справа и компактное меню, игровой режим с приставкой по HDMI, строки «Режим изображения» и «Плавность движения» в панели «Сигнал».
  • Если что-то не работает, напишите модель, версию прошивки XGIMI и что делали.

Что пока нельзя

  • Установить Lumen OS насовсем.

---

Beta 3. Lumen OS for the XGIMI TITAN Noir Pro (H0062). Trial only.

New

  • The new setup wizard, as on the Z9X: right after the language a Theme step with Light, Dark or Auto. Before, the build kept the wizard of version 1.0.9.
  • When the projector starts after being unplugged, the Lumen melody plays with the boot logo. Before, it played only when the projector woke from standby.
  • The projector menu can sit on the right: All settings, General, the Menu group. The menu size is there too: normal or compact, the compact one fits more rows on the screen. On the right the whole menu is mirrored.
  • Image correction: Autofocus now and Manual focus sit right under the manual keystone, the smart autofocus settings have their own page. Restore the original picture is now called Restore screen to default.
  • Game mode: the picture settings are no longer closed as a whole. Only the rows that add delay are closed: motion compensation, noise reduction, super resolution and Ultra 120 Hz.
  • Anti rainbow no longer resets the colour temperature, and turning game mode on or off no longer turns off HDR10 dynamic tone mapping. After a picture mode change the menu sets your sharpness again.
  • The menu no longer closes when the HDMI input restarts its screen while it agrees on the signal.
  • Light theme: the selected quick menu tile and the selected row in its windows and in All settings are filled with a deeper blue, the white text on it reads better.
  • Signal panel: new Picture mode and Motion smoothing rows, with the same names as in the menu. The picture mode shows on the small card too.

The trial starts in English. Other languages and your time zone are in the Android settings. This beta has not run on a real TITAN Noir Pro yet, everything new is checked by tests and on an emulator only. If something is wrong, write to us.

How to start the trial

  • Your projector needs XGIMI firmware V1.2.99 or V1.2.54.
  • Download the Lumen Installer file that ends in .apk1 from https://github.com/Project-Lumen-OS/lumen-installer/releases/latest If Lumen Installer is already on the projector, update it from the same page. How to put the app on the projector from a USB stick: https://github.com/Project-Lumen-OS/lumen-os/blob/main/docs/install/en.md
  • Open Lumen Installer. This model has only a beta, so the beta is chosen. Press "Get the trial ready", then "Start Lumen OS", then restart the projector.
  • You do not need to download the files of this release, Lumen Installer gets them itself.

How to go back to the XGIMI system

  • Just restart the projector. The XGIMI system starts as it was, the trial does not change it.

If the XGIMI system does not start by itself

  • This should not happen. A recovery USB stick brings it back: MBR, FAT32 format, only the file XGIMI_HORSEPOPULAR_XR04EOS.bin on the stick itself, not in a folder (firmware V1.2.99, 2 519 405 360 bytes). On a Mac copy it with cp -X. Link: https://product-library.static.xgimi.com/firmware/release/MTK9681/dianahy/MTK9681_DOHKO_1.2.99_20260907-104602/XGIMI_HORSEPOPULAR_XR04EOS.bin
  • Put the stick in, unplug the projector, hold the power button on the projector itself, plug it in and keep holding until the update screen shows. Everything on the projector is erased and the XGIMI system starts.

What to check and send

  • The melody when the projector starts after being unplugged, the setup wizard of the trial, the menu on the right and the compact menu, game mode with a console on HDMI, the Picture mode and Motion smoothing rows of the Signal panel.
  • If something does not work, write your model, XGIMI firmware version and what you did.

Not yet

  • Installing Lumen OS for good.

XGIMI TITAN Noir 1.0.10-beta3

БетаGitHub

Бета 3. Lumen OS для XGIMI TITAN Noir (H0061). Только пробный запуск.

Что нового

  • Главный экран: у каждого из трёх входов HDMI своя кнопка внизу. Теперь там HDMI 1, HDMI 2, HDMI 3 и ещё одна кнопка: флешка или «Источник» со всем остальным. Раньше HDMI 3 прятался за кнопкой «Источник», если была подключена флешка или повтор экрана.
  • Кнопки пульта: в список действий добавлены «HDMI 3» и «Датчики». Выбранная строка на странице кнопок теперь светлая с тёмным текстом, как в меню проектора.
  • Режим Dolby Vision: новая строка с выбором «Dolby Vision Bright» и «Dolby Vision Dark», как в заводской прошивке XGIMI. Она стоит над «Настройками Dolby Vision» и работает, пока идёт видео Dolby Vision.
  • «Все настройки», HDMI, «Параметры входа»: страница в новом виде меню, светлая или тёмная по теме. Переключатели вместо флажков, «Источник при включении» меняется кнопками влево и вправо, внизу входы HDMI и что к ним подключено.
  • Панель «Сигнал» больше не пишет «DVI, без звука» при обычном HDMI со звуком. Строка «Режим входа» называется «Режим HDMI», как в меню, строка «Порт» называется «Возможности порта». Строка «Плавность» теперь «Кадровая частота», её легко было спутать с «Плавностью движения» из меню.
  • Карточка «Датчики» стоит справа, там же, где карточка сигнала, и долгое нажатие OK раскрывает её на месте. Пока на экране карточка сигнала или датчиков, долгое нажатие OK на главном экране раскрывает карточку и больше не открывает меню плитки.
  • Голосовой поиск: «IPTV», «ТВ каналы», «телевизор» и такие же слова на других языках больше не открывают Lumen Play. Открывается установленное приложение для телеканалов или Lampa, а если их нет, поиск.

Проба запускается на английском. Русский и другие языки, а также часовой пояс выбираются в настройках Android. Эта бета на настоящем TITAN Noir ещё не запускалась, всё новое проверено только тестами и на эмуляторе. Если что-то не так, напишите.

Как запустить пробу

  • Нужна прошивка XGIMI V1.2.99 или V1.2.54.
  • Скачайте файл Lumen Installer, который заканчивается на .apk1, отсюда: https://github.com/Project-Lumen-OS/lumen-installer/releases/latest Если Lumen Installer уже стоит, обновите его оттуда же. Как поставить приложение с флешки, написано в инструкции: https://github.com/Project-Lumen-OS/lumen-os/blob/main/docs/install/ru.md
  • Откройте Lumen Installer. У этой модели есть только бета, она и будет выбрана. Нажмите «Подготовить пробный запуск», потом «Запустить Lumen OS» и перезапустите проектор.
  • Файлы этого выпуска скачивать не нужно, Lumen Installer берёт их сам.

Как вернуться в систему XGIMI

  • Просто перезапустите проектор. Система XGIMI запустится как была, проба в ней ничего не меняет.

Если система XGIMI сама не запускается

  • Так быть не должно. Вернуть её можно флешкой восстановления: таблица MBR, формат FAT32, в корне только файл XGIMI_HORSEPOPULAR_XR06EOS.bin (прошивка V1.2.99, 2 519 405 360 байт). На Mac копируйте командой cp -X. Ссылка: https://product-library.static.xgimi.com/firmware/release/MTK9681/dianahy/MTK9681_DOHKO_1.2.99_20260907-104602/XGIMI_HORSEPOPULAR_XR06EOS.bin
  • Вставьте флешку, выдерните шнур питания, зажмите кнопку питания на самом проекторе, вставьте шнур и держите кнопку, пока не появится экран обновления. Всё на проекторе сотрётся, запустится система XGIMI.

Что проверить и прислать

  • Кнопки HDMI 1, HDMI 2 и HDMI 3 на главном экране, режим Dolby Vision с видео Dolby Vision, строку «Подключение» в панели «Сигнал» с приставкой по HDMI, страницу «Параметры входа», карточку «Датчики», голосовой поиск со словами «ТВ каналы».
  • Если что-то не работает, напишите модель, версию прошивки XGIMI и что делали.

Что пока нельзя

  • Установить Lumen OS насовсем.

---

Beta 3. Lumen OS for the XGIMI TITAN Noir (H0061). Trial only.

New

  • Home screen: each of the three HDMI inputs has its own button at the bottom. Now there are HDMI 1, HDMI 2, HDMI 3 and one more button: the USB stick or Source with everything else. Before, HDMI 3 hid behind the Source button when a USB stick or screen mirroring was there.
  • Remote buttons: HDMI 3 and Sensors are now in the list of actions. The selected row on the buttons page is now light with dark text, as in the projector menu.
  • Dolby Vision mode: a new row with Dolby Vision Bright and Dolby Vision Dark, as in the XGIMI factory firmware. It sits above Dolby Vision settings and works while Dolby Vision video plays.
  • All settings, HDMI, Input options: the page has the new menu look, light or dark with the theme. Switches instead of checkboxes, Source at power on changes with left and right, the HDMI inputs and what is connected to them at the bottom.
  • The Signal panel no longer says DVI, no sound for normal HDMI with sound. The Input mode row is now called HDMI mode, as in the menu, the Port row is now called Port features. The Smoothness row is now Frame rate, it was easy to mix up with Motion smoothing in the menu.
  • The Sensors card sits on the right, where the signal card is, and a long press of OK opens it in place. While the signal or sensors card is on the screen, a long press of OK on the home screen opens the card and no longer opens the tile menu.
  • Voice search: IPTV, TV channels, television and the same words in the other languages no longer open Lumen Play. An installed TV channels app or Lampa opens, and search when there is none.

The trial starts in English. Other languages and your time zone are in the Android settings. This beta has not run on a real TITAN Noir yet, everything new is checked by tests and on an emulator only. If something is wrong, write to us.

How to start the trial

  • Your projector needs XGIMI firmware V1.2.99 or V1.2.54.
  • Download the Lumen Installer file that ends in .apk1 from https://github.com/Project-Lumen-OS/lumen-installer/releases/latest If Lumen Installer is already on the projector, update it from the same page. How to put the app on the projector from a USB stick: https://github.com/Project-Lumen-OS/lumen-os/blob/main/docs/install/en.md
  • Open Lumen Installer. This model has only a beta, so the beta is chosen. Press "Get the trial ready", then "Start Lumen OS", then restart the projector.
  • You do not need to download the files of this release, Lumen Installer gets them itself.

How to go back to the XGIMI system

  • Just restart the projector. The XGIMI system starts as it was, the trial does not change it.

If the XGIMI system does not start by itself

  • This should not happen. A recovery USB stick brings it back: MBR, FAT32 format, only the file XGIMI_HORSEPOPULAR_XR06EOS.bin on the stick itself, not in a folder (firmware V1.2.99, 2 519 405 360 bytes). On a Mac copy it with cp -X. Link: https://product-library.static.xgimi.com/firmware/release/MTK9681/dianahy/MTK9681_DOHKO_1.2.99_20260907-104602/XGIMI_HORSEPOPULAR_XR06EOS.bin
  • Put the stick in, unplug the projector, hold the power button on the projector itself, plug it in and keep holding until the update screen shows. Everything on the projector is erased and the XGIMI system starts.

What to check and send

  • The HDMI 1, HDMI 2 and HDMI 3 buttons on the home screen, Dolby Vision mode with Dolby Vision video, the Connection row of the Signal panel with a console on HDMI, the Input options page, the Sensors card, voice search with the words TV channels.
  • If something does not work, write your model, XGIMI firmware version and what you did.

Not yet

  • Installing Lumen OS for good.

XGIMI TITAN Noir Max 1.0.10-beta3

БетаGitHub

Вышла бета 4, ставьте её: https://github.com/Project-Lumen-OS/lumen-os/releases/tag/titanmax-1.0.10-beta4 . Beta 4 is out, use it instead.

Бета 3. Lumen OS для XGIMI TITAN Noir Max (H0063). Только пробный запуск.

Что нового

  • Новый мастер первой настройки, как на Z9X: сразу после языка шаг «Оформление» со светлой, тёмной или автоматической темой. Раньше в сборке оставался мастер из версии 1.0.9.
  • При включении из розетки мелодия Lumen звучит вместе с заставкой. Раньше она звучала только при выходе из режима ожидания.
  • Меню проектора можно поставить справа: «Все настройки», «Общие», группа «Меню». Там же размер меню: обычный или компактный, в компактном на экран помещается больше строк. Справа меню отражено целиком.
  • «Коррекция изображения»: «Автофокус сейчас» и «Ручной фокус» стоят сразу под ручной коррекцией трапеции, настройки умного автофокуса на своей странице. «Вернуть исходное изображение» теперь называется «Вернуть экран к исходному».
  • Игровой режим: настройки изображения больше не закрыты целиком. Закрыты только строки, которые добавляют задержку: компенсация движения, шумоподавление, суперразрешение и Ultra 120 Гц.
  • «Анти-радуга» больше не сбрасывает цветовую температуру, а включение и выключение игрового режима не выключает динамическое тональное отображение HDR10. После смены режима изображения меню снова ставит вашу резкость.
  • Меню больше не закрывается, когда вход HDMI перезапускает экран при согласовании сигнала.
  • Светлая тема: выбранная плитка быстрого меню и выбранная строка в его окнах и в «Все настройки» закрашены более глубоким синим, белый текст на нём читается лучше.
  • Панель «Сигнал»: новые строки «Режим изображения» и «Плавность движения», названия те же, что в меню. Режим изображения виден и на маленькой карточке.

Проба запускается на английском. Русский и другие языки, а также часовой пояс выбираются в настройках Android. Эта бета на настоящем TITAN Noir Max ещё не запускалась, всё новое проверено только тестами и на эмуляторе. Если что-то не так, напишите.

Как запустить пробу

  • Нужна прошивка XGIMI V1.2.99 или V1.2.54.
  • Скачайте файл Lumen Installer, который заканчивается на .apk1, отсюда: https://github.com/Project-Lumen-OS/lumen-installer/releases/latest Если Lumen Installer уже стоит, обновите его оттуда же. Как поставить приложение с флешки, написано в инструкции: https://github.com/Project-Lumen-OS/lumen-os/blob/main/docs/install/ru.md
  • Откройте Lumen Installer. У этой модели есть только бета, она и будет выбрана. Нажмите «Подготовить пробный запуск», потом «Запустить Lumen OS» и перезапустите проектор.
  • Файлы этого выпуска скачивать не нужно, Lumen Installer берёт их сам.

Как вернуться в систему XGIMI

  • Просто перезапустите проектор. Система XGIMI запустится как была, проба в ней ничего не меняет.

Если система XGIMI сама не запускается

  • Так быть не должно. Вернуть её можно флешкой восстановления: таблица MBR, формат FAT32, в корне только файл XGIMI_HORSEPOPULAR_XR03EOS.bin (прошивка V1.2.99, 2 519 405 360 байт). На Mac копируйте командой cp -X. Ссылка: https://product-library.static.xgimi.com/firmware/release/MTK9681/dianahy/MTK9681_DOHKO_1.2.99_20260907-104602/XGIMI_HORSEPOPULAR_XR03EOS.bin
  • Вставьте флешку, выдерните шнур питания, зажмите кнопку питания на самом проекторе, вставьте шнур и держите кнопку, пока не появится экран обновления. Всё на проекторе сотрётся, запустится система XGIMI.

Что проверить и прислать

  • Мелодию при включении из розетки, первую настройку пробы, меню справа и компактное меню, игровой режим с приставкой по HDMI, строки «Режим изображения» и «Плавность движения» в панели «Сигнал».
  • Если что-то не работает, напишите модель, версию прошивки XGIMI и что делали.

Что пока нельзя

  • Установить Lumen OS насовсем.

---

Beta 3. Lumen OS for the XGIMI TITAN Noir Max (H0063). Trial only.

New

  • The new setup wizard, as on the Z9X: right after the language a Theme step with Light, Dark or Auto. Before, the build kept the wizard of version 1.0.9.
  • When the projector starts after being unplugged, the Lumen melody plays with the boot logo. Before, it played only when the projector woke from standby.
  • The projector menu can sit on the right: All settings, General, the Menu group. The menu size is there too: normal or compact, the compact one fits more rows on the screen. On the right the whole menu is mirrored.
  • Image correction: Autofocus now and Manual focus sit right under the manual keystone, the smart autofocus settings have their own page. Restore the original picture is now called Restore screen to default.
  • Game mode: the picture settings are no longer closed as a whole. Only the rows that add delay are closed: motion compensation, noise reduction, super resolution and Ultra 120 Hz.
  • Anti rainbow no longer resets the colour temperature, and turning game mode on or off no longer turns off HDR10 dynamic tone mapping. After a picture mode change the menu sets your sharpness again.
  • The menu no longer closes when the HDMI input restarts its screen while it agrees on the signal.
  • Light theme: the selected quick menu tile and the selected row in its windows and in All settings are filled with a deeper blue, the white text on it reads better.
  • Signal panel: new Picture mode and Motion smoothing rows, with the same names as in the menu. The picture mode shows on the small card too.

The trial starts in English. Other languages and your time zone are in the Android settings. This beta has not run on a real TITAN Noir Max yet, everything new is checked by tests and on an emulator only. If something is wrong, write to us.

How to start the trial

  • Your projector needs XGIMI firmware V1.2.99 or V1.2.54.
  • Download the Lumen Installer file that ends in .apk1 from https://github.com/Project-Lumen-OS/lumen-installer/releases/latest If Lumen Installer is already on the projector, update it from the same page. How to put the app on the projector from a USB stick: https://github.com/Project-Lumen-OS/lumen-os/blob/main/docs/install/en.md
  • Open Lumen Installer. This model has only a beta, so the beta is chosen. Press "Get the trial ready", then "Start Lumen OS", then restart the projector.
  • You do not need to download the files of this release, Lumen Installer gets them itself.

How to go back to the XGIMI system

  • Just restart the projector. The XGIMI system starts as it was, the trial does not change it.

If the XGIMI system does not start by itself

  • This should not happen. A recovery USB stick brings it back: MBR, FAT32 format, only the file XGIMI_HORSEPOPULAR_XR03EOS.bin on the stick itself, not in a folder (firmware V1.2.99, 2 519 405 360 bytes). On a Mac copy it with cp -X. Link: https://product-library.static.xgimi.com/firmware/release/MTK9681/dianahy/MTK9681_DOHKO_1.2.99_20260907-104602/XGIMI_HORSEPOPULAR_XR03EOS.bin
  • Put the stick in, unplug the projector, hold the power button on the projector itself, plug it in and keep holding until the update screen shows. Everything on the projector is erased and the XGIMI system starts.

What to check and send

  • The melody when the projector starts after being unplugged, the setup wizard of the trial, the menu on the right and the compact menu, game mode with a console on HDMI, the Picture mode and Motion smoothing rows of the Signal panel.
  • If something does not work, write your model, XGIMI firmware version and what you did.

Not yet

  • Installing Lumen OS for good.

XGIMI Z9X HB 1.0.10-beta21

БетаGitHub

Бета 21 для XGIMI Z9X HB (G0130, G0148). Это тестовая сборка, а не основной выпуск. В ней могут быть ошибки.

Что нового

  • Обновления скачиваются быстрее. Lumen качает файл обновления сразу по нескольким соединениям, поэтому ограничение скорости одного соединения у провайдера почти не мешает. После обрыва сети, паузы или перезапуска загрузка продолжается с того места, где остановилась. Готовый файл проверяется как раньше. Эта бета ещё скачивается по старому, быстрее станут следующие обновления.
  • «Цветовое пространство» в профессиональных настройках изображения теперь видно и с HDR источником, как в системе XGIMI. Если проектор не принял выбор при HDR, строка показывает настоящее значение и подсказку XGIMI.
  • Меню проектора можно поставить справа: «Все настройки», «Общие», группа «Меню». Там же размер меню: обычный или компактный, в компактном на экран помещается больше строк. Справа меню отражено целиком.
  • «Коррекция изображения»: «Автофокус сейчас» и «Ручной фокус» стоят сразу под ручной коррекцией трапеции, настройки умного автофокуса на своей странице. «Вернуть исходное изображение» теперь называется «Вернуть экран к исходному».
  • Светлая тема: выбранная плитка быстрого меню и выбранная строка в его окнах и в «Все настройки» закрашены более глубоким синим, белый текст на нём читается лучше.
  • Страница «Вывод звука» обновляется сама. После включения eARC сразу видно, что звук идёт на саундбар, закрывать и открывать страницу больше не нужно.
  • Панель «Сигнал» на странице «Для разработчиков»: новые строки «Режим изображения» и «Плавность движения», режим изображения виден и на маленькой карточке. В полной панели ещё данные HDR фильма (яркость и цвета мастеринга, MaxCLL и MaxFALL), имя устройства на входе и скорость линии HDMI. Частота кадров показывается ровно, случайных значений вроде 133 Гц больше нет. Подсказка «Удерживайте OK, чтобы раскрыть» видна каждый раз, когда карточку открывает назначенная ей кнопка пульта, пока вы ни разу её не раскрыли.

Всё новое пока проверено тестами, на проекторе ещё нет. Если что-то не так, отправьте отчёт в «Все настройки», «Общие» или напишите, что делали и что увидели.

Как получить

Уже стоит Lumen OS с включёнными «Бета-обновлениями»? Эта версия придёт сама. Она скачивается целиком, около 450 МБ. Данные сохраняются.

Для пробного запуска поставьте на проектор Lumen Installer, это файл, который заканчивается на .apk1. Откройте его и выберите «Версия: бета». Чтобы установить насовсем, в пробе откройте «Установить Lumen OS».

Какие проекторы

  • G0130 с прошивкой XGIMI 6.16.24 или 6.17.12: проба и установка.
  • G0148 с прошивкой XGIMI 6.17.12: проба и установка.
  • G0118: пока не поддерживается.

Не ставьте прошивку 6.16.24 на проектор, который пришёл с 6.17.12.

Как вернуться

Во время пробы просто перезапустите проектор. После установки вернуть систему XGIMI можно флешкой восстановления XGIMI для вашей модели (откат на сток). Для G0148 нужен файл прошивки 6.17.12.

Файлы: lumen-os-hb-1.0.10-beta21-nogms-system.img (образ системы), SHA256SUMS и SHA256SUMS.sig (контрольная сумма и подпись), lumen-os-hb-1.0.10-beta21-nogms-full-ota.zip и lumen-os-hb-1.0.10-beta21-nogms-full-payload_metadata.bin (обновление, его берёт сам проектор).

---

Beta 21 for the XGIMI Z9X HB (G0130, G0148). This is a test build, not a main release. It may have bugs.

What is new

  • Updates download faster. Lumen fetches the update file over several connections at once, so a provider's speed limit per connection hardly matters. After a network drop, a pause or a restart the download goes on from where it stopped. The finished file is checked as before. This beta still downloads the old way, the next updates come faster.
  • Colour space in the professional picture settings now shows with an HDR source too, as in the XGIMI system. If the projector does not take the choice with HDR, the row shows the real value and the XGIMI hint.
  • The projector menu can sit on the right: All settings, General, the Menu group. The menu size is there too: normal or compact, the compact one fits more rows on the screen. On the right the whole menu is mirrored.
  • Image correction: Autofocus now and Manual focus sit right under the manual keystone, the smart autofocus settings have their own page. Restore the original picture is now called Restore screen to default.
  • Light theme: the selected quick menu tile and the selected row in its windows and in All settings are filled with a deeper blue, the white text on it reads better.
  • The Sound output page updates by itself. After you turn on eARC it shows at once that the sound goes to the soundbar, no need to close and open the page.
  • The Signal panel on the For developers page: new Picture mode and Motion smoothing rows, the picture mode shows on the small card too. The full panel also shows the film's HDR data (mastering brightness and colours, MaxCLL and MaxFALL), the name of the device on the input and the HDMI link speed. The frame rate shows steady, random values such as 133 Hz are gone. The Hold OK to open hint shows every time the card is opened by the remote button you gave it, until you have opened the card once.

Everything new is checked by tests only so far, not on a projector yet. If something does not work right, send a report from All settings, General or write what you did and what you saw.

How to get it

Lumen OS already installed with Beta updates on? This version comes by itself. It downloads in full, about 450 MB. Your data stays.

For a trial run put Lumen Installer on the projector, the file that ends in .apk1. Open it and choose Version: beta. To install for good, open Install Lumen OS in the trial.

Which projectors

  • G0130 with XGIMI firmware 6.16.24 or 6.17.12: trial and install.
  • G0148 with XGIMI firmware 6.17.12: trial and install.
  • G0118: not supported yet.

Do not put firmware 6.16.24 on a projector that came with 6.17.12.

Going back

During the trial just restart the projector. After an install, the XGIMI recovery USB stick of your model brings the XGIMI system back (back to stock). The G0148 needs the 6.17.12 firmware file.

Files: lumen-os-hb-1.0.10-beta21-nogms-system.img (the system image), SHA256SUMS and SHA256SUMS.sig (checksum and signature), lumen-os-hb-1.0.10-beta21-nogms-full-ota.zip and lumen-os-hb-1.0.10-beta21-nogms-full-payload_metadata.bin (the update, the projector takes it by itself).